Ryobi A25RT02 User Manual download pdf (Page 7)

ELECTRICAL

SPEED AND WIRING

The no-load speed of this product depends on the router

you are using. This speed is not constant and decreases

under a load or with lower voltage. For voltage, the wiring

in a shop is as important as the motor’s horsepower rating.

A line intended only for lights cannot properly carry a power

product motor. Wire that is heavy enough for a short dis-

tance will be too light for a greater distance. A line that can

support one power product may not be able to support two

or three products.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding pro-

vides a path of least resistance for electric current to reduce

the risk of electric shock. This product is equipped with an

electric cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into a matching

outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet,

have the proper outlet installed by a qualified electrician.

Improper connection of the equipment-grounding conduc-

tor can result in a risk of electric shock. The conductor with

insulation having an outer surface that is green with or without

yellow stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary, do

not connect the equipment-grounding conductor to a live

terminal.

Check with a qualified electrician or service personnel if the

grounding instructions are not completely understood, or if

in doubt as to whether the product is properly grounded.

Repair or replace a damaged or worn cord immediately.

This product is intended for use on a circuit that has an outlet

like the one shown in figure 1. It also has a grounding pin

like the one shown.

Fig. 1

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong grounding

plugs and 3-pole receptacles that accept the product’s plug.

When using a power product at a considerable distance from

the power source, use an extension cord heavy enough to

carry the current that the product will draw. An undersized

extension cord will cause a drop in line voltage, resulting in

a loss of power and causing the motor to overheat. Use the

chart provided below to determine the minimum wire size

required in an extension cord. Only round jacketed cords

listed by Underwriter’s Laboratories (UL) should be used.

**Ampere rating (on product data plate)

0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0

Cord Length Wire Size (A.W.G.)

25' 16 16 16 16 14 14

' 16 16 16 14 14 12

100

' 16 16 14 12 10 —

**Used on 12 gauge - 20 amp circuit.

NOTE: AWG = American Wire Gauge

When working with the product outdoors, use an extension

cord that is designed for outside use. This is indicated by the

letters “WA” on the cord’s jacket.

Before using an extension cord, inspect it for loose or

exposed wires and cut or worn insulation.

WARNING:

Keep the extension cord clear of the working area.

Position the cord so that it will not get caught on lumber,

products or other obstructions while you are working with

a power product. Failure to do so can result in serious

personal injury.

WARNING:

Check extension cords before each use. If damaged

replace immediately. Never use product with a damaged

cord since touching the damaged area could cause elec-

trical shock resulting in serious injury.

ELECTRICAL CONNECTION

This product should be connected to a power supply that is

120 volts, 60 Hz, AC only (normal household current). Do

not operate this product on direct current (DC). A substantial

voltage drop will cause a loss of power and the motor will

overheat. If the router table does not operate when plugged

into an outlet, double check the power supply.

GROUNDING

120 V GROUNDED OUTLET

1 2 3 4 5 6 7 8 9 10 11 12 ... 19 20

Comments to this Manuals

No comments

Ryobi A25RT02 User Manual Page 7

Comments to this Manuals

Related products and manuals for Routers Ryobi A25RT02