SAVE THIS MANUAL FOR FUTURE REFERENCEOPERATOR’S MANUAL10 in. Compound Miter SawTS1343L - Double InsulatedYour miter saw has been engineered and manufa
10FEATURESKNOW YOUR COMPOUND MITER SAWSee Figure 1.The safe use of this product requires an understanding of the information on the tool and in this o
11FEATURESMITER LOCK HANDLESee Figure 2.The miter lock handle securely locks the saw at desired miter angles.POSITIVE STOPS ON MITER TABLEPositive sto
12LOOSE PARTSWARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The following items a
13ASSEMBLYFig. 7MOUNTING SURFACE BASETRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNTRACE HOLES AT THESE LOCATIONS FOR HOLE PATTERNWARNING:Do not con
14ASSEMBLYFig. 8Fig. 10TO LOOSENMITER LOCK HANDLETO TIGHTENDUST BAGEXHAUST PORTBASEWORK CLAMPMITER LOCK HANDLESee Figure 8.To install the miter lock h
15INSTALLING BATTERIES IN LASERSee Figure 11.Remove screw from battery compartment cover using the Phillips end of the supplied blade wrench. Remove
16ASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 13 - 14.WARNING:A 10 in. blade is the maximum blade capacity of the saw. Never use a blade that is
17ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock button when
18ASSEMBLYSQUARING THE SAW BLADE TO THE FENCESee Figures 18 - 22 Unplug the saw. Pull the saw arm all the way down and engage the lock pin to hold
19ASSEMBLYFig. 22SQUARING THE BLADE TO THE MITER TABLESee Figures 22 - 25. Unplug the saw. Pull the saw arm all the way down and engage the lock p
2 Introduction ...
20OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second is sufficient to inflict s
21OPERATION Rotate the control arm until the pointer aligns with the desired angle on the miter scale. Release the miter lock plate. NOTE: You c
22OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece w
23OPERATION Grasp the stock firmly with one hand and secure it against the fence. Use the optional work clamp or a C-clamp to secure the workpiece w
24OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M-
25OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes the
26OPERATIONWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against the
27ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul
28ADJUSTMENTSDANGER:Laser radiation. Avoid direct eye contact with light source.WARNING:Use of controls or adjustments or performance of pro-cedures o
29MAINTENANCEWARNING:When servicing, use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage.WA
3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir
• SERVICENow that you have purchased your tool, should a need ever exist for repair parts or service, simply contact your nearest Authorized Service
4GENERAL SAFETY RULES INSPECT TOOL CORDS PERIODICALLY. If damaged, have repaired by a qualified service technician at an authorized service facilit
5SPECIFIC SAFETY RULES NEVER reach behind, under, or within three inches of the blade and its cutting path with hands and fingers for any reason.
6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols wil
7EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to hand
8GLOSSARY OF TERMSPush Blocks (for jointer planers)Device used to feed the workpiece over the jointer planer cutterhead during any operation. This aid
9FEATURESPRODUCT SPECIFICATIONSBlade Arbor ................ 5/8 in.Blade Diameter .......
Comments to this Manuals