Ryobi P330 User Manual download pdf (Page 10)

10 — English

SINGLE SEQUENTIAL ACTUATION MODE

Single sequential actuation provides the most accurate

fastener placement.

 Remove battery pack from the tool.

 Slide the selector to position ( ).

WARNING:

The nailer will not function properly if the selector

is not securely seated in either position ( ) or

( ). Always assure the selector is seated properly to

avoid an unexpected nail discharge and possible serious

personal injury.

 Reinstall the battery pack.

 Grip the tool firmly to maintain control. Position the nose

of the tool onto the work surface.

 Push the tool against the work surface to depress the

workpiece contact.

 Squeeze the trigger to drive a fastener.

NOTE: Hold trigger until drive cycle is complete. If depressing

the trigger does not drive a fastener, lift the tool away from

the workpiece, then replace and try driving the fastener again.

CONTACT ACTUATION MODE

Contact actuation allows very fast repetitive fastener

placement.

 Remove the battery pack from the tool.

 Slide the selector to position ( ).

 Reinstall the battery pack.

 Grip the tool firmly to maintain control.

 Squeeze and hold the trigger. Push the tool against the

work surface to depress the workpiece contact and drive

a nail.

NOTE: Hold trigger and keep workpiece contact

depressed until drive cycle is complete.

 Always remove your finger from the trigger when the

desired number of nails has been driven.

NOTE: In Contact Actuation Mode, the tool may also be

operated by depressing the workpiece contact against the

surface and squeezing the trigger.

WARNING:

During normal use the tool will recoil immediately

after driving a fastener. This is a normal function of the

tool. Do not attempt to prevent the recoil by holding the

nailer against the work. Restriction to the recoil can result

in a second fastener being driven from the nailer. Failure

to heed this warning can result in serious personal injury.

OPERATION

DRY-FIRE LOCKOUT

When the magazine has 0-5 nails remaining, the dry-fire

lockout feature will not allow continued operation.

To resume operation, reload the tool with nails.

LED WORKLIGHT

See Figure 10, page 15.

 To turn on the LEDs, press LED worklight grip switch

while firmly holding tool during normal operation.

DIAGNOSTIC FEEDBACK

The LED Worklight provides feedback to indicate whether

the battery pack is charged sufficiently and/or if the tool is

functioning properly.

If worklight is flashing, install fully charged battery. If light

continues to flash, see Troubleshooting section for more

information.

If the LED light goes out on your nailer, the unit has timed

out for your protection. Lift tool from the workpiece and

release trigger to reactivate the nailer before beginning next

drive cycle.

REMOVING NAILS FROM THE TOOL

See Figure 11, page 15.

WARNING:

Remove the battery pack before removing nails or

clearing a jammed nail. Failure to do so could result in

serious personal injury.

 To remove a strip of nails from the tool, hold the finish

nailer by the handle with your right hand, and rest your

left hand underneath the tool with your left thumb on the

pusher.

 Depress the release button and slide the pusher all the

way to the rear of the magazine until it locks in place.

NOTE: Always keep fingers clear of nail track of magazine

to prevent injury from unintended release of the pusher.

 Slide the nails toward the back of the magazine and

remove.

CLEARING A JAMMED FASTENER

See Figure 12, page 15.

WARNING:

Remove the battery pack from the tool before clearing a

jammed fastener. Failure to do so could result in serious

personal injury.

Driving too deeply into the material, excess debris, or jammed

nails may lead to the driver mechanism being stuck at its

bottom position.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 ... 35 36

Comments to this Manuals

No comments

Ryobi P330 User Manual Page 10

Comments to this Manuals

Related products and manuals for Tools Ryobi P330