Ryobi BT3000 Operator's Manual download pdf

OPERATOR'S MANUAL

#4950300 ROUTER AND JIG SAW MOUNTING KIT

(FOR USE WITH THE BT3000 TABLE SAW)

Save This Manual For Future Reference

CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT.

Your new #4950300 Router and Jig Saw Mounting Kit has been designed for use with the RYOBI BT3000 Table Saw. It

has been engineered and manufactured to Ryobi’s high standards for dependability, ease of operation, and operator safety.

This kit gives you the capability of mounting a router or jig saw on the accessory table of your BT3000. It also includes a circle

cutting jig for cutting circular patterns in both large and small stock. Properly cared for, it will provide years of dependable,

trouble-free performance.

RULES FOR SAFE OPERATION

1. READ THESE INSTRUCTIONS THOROUGHLY before assembling or using this router and jig saw mounting kit.

2. READ THE INSTRUCTIONS FOR THE BT3000 TABLE SAW before operating your saw with this kit.

3. KEEP ASSEMBLY AREA AND WORK AREA CLEAN. Cluttered areas and benches invite accidents.

4. ALWAYS WEAR SAFETY GLASSES . Everyday eyeglasses have only impact-resistant lenses; they are NOT safety

glasses.

5. DO NOT USE THIS PRODUCT WITH OTHER EQUIPMENT OR FOR OTHER PURPOSES.

6. ALWAYS DISCONNECT SAW FROM POWER SUPPLY BEFORE ASSEMBLING THIS KIT. Make sure switch is off

when reconnecting saw to power supply.

1 2 ... 14

Summary of Contents

Page 1 - RULES FOR SAFE OPERATION

OPERATOR'S MANUAL#4950300 ROUTER AND JIG SAW MOUNTING KIT(FOR USE WITH THE BT3000 TABLE SAW)Save This Manual For Future ReferenceCONGRATULATIONS

Page 2

Page 10CIRCLE CUTTING JIGCIRCLE CUTTINGSee Figures 13-16.The circle cutting jig makes it possible to cut and shapecircular patterns in both large and

Page 3 - LIST OF LOOSE PARTS

Page 11TO PLACE WORKPIECE ON SAW TABLESSee Figure 15.As mentioned previously there are many variables that influence a circle being cut or shaped. The

Page 4 - ASSEMBLY

Page 12#4950300 ROUTER AND JIG SAW MOUNTING KIT1234554367891011121314151617182019421222423253

Page 5 - ROUTER MOUNTING (Cont'd)

Page 13REPLACEMENT PARTSNow that you have purchased your Router and Jig Saw Mounting Kit, should a need ever exist for repairparts or service, simply

Page 6

RYOBI TECHNOLOGIES INC.1428 Pearman Dairy Road Anderson SC 29625Post Office Box 1207 Anderson SC 29622-1207Phone 1-800-525-2579612547-852OPERATOR&

Page 7

Page 2RULES FOR SAFE OPERATION (Continued)7. DO NOT MAKE ADJUSTMENTS UNTIL CUTTER OR BLADE HAS COME TO A COMPLETE STOP AND TOOL HASBEEN DISCONNECTED F

Page 8 - JIG SAW MOUNTING

Page 3DESCRIPTION QUANTITYGuide Fence with Guide Block ... 2Knob Bolt (#5/16-18 x 1/2 in.) ...

Page 9 - REMEMBER:

Page 4ASSEMBLYRead these instructions completely before beginning assembly of this kit.WARNING:The saw's motor cord must be disconnected from the

Page 10 - CIRCLE CUTTING JIG

Page 5ROUTER MOUNTING (Cont'd)TO INSTALL GUIDE FENCE BRACKETSSee Figure 4.1. Align each guide fence bracket with two of the special 5/16 in. T-nu

Page 11 - See Figure 16

Page 6ROUTER MOUNTING (Cont'd)TO ASSEMBLE RE600 ELECTRONIC ROUTERTO ROUTER MOUNTING PLATESee Figures 5 and 6.1. Remove the subbase screws and sub

Page 12

Page 7ROUTER MOUNTING (Cont'd)TO ASSEMBLE TABLE CLAMPING BRACKET(Cont'd)1. Remove end cap from rear rail as shown in figure 8.2. Slide one o

Page 13 - PARTS LIST

Page 8Fig. 11Fig. 10When used for jig saw mounting, this kit can be used with allRyobi jig saws, plus most other brands of jig saws. Propermounting of

Page 14

Page 9JIG SAW MOUNTING (Cont'd)TO ASSEMBLE MOUNTING PLATE WITH JIG SAW ATTACHED TO ACCESSORY TABLESee Figure 12.1. Place mounting plate under acc