Ryobi WS721 User Manual download pdf (Page 4)

4 — English

GENERAL SAFETY RULES

 KEEP HANDS AWAY FROM CUTTING AREA. Keep

hands away from wheels. Do not reach underneathwork

or around or over the wheel while wheel is rotating. Do not

attempt to remove cut material when wheel is moving.

WHEEL COASTS AFTER BEING TURNED OFF.

 NEVER USE IN AN EXPLOSIVE ATMOSPHERE.

Normal sparking of the motor could ignite fumes.

 INSPECT TOOL CORDS PERIODICALLY. If dam-

aged, have repaired by a qualified service technician at

an authorized service facility. The conductor with insulation

having an outer surface that is green with or without yellow

stripes is the equipment-grounding conductor. If repair

or replacement of the electric cord or plug is necessary,

do not connect the equipment-grounding conductor to a

live terminal. Repair or replace a damaged or worn cord

immediately. Stay constantly aware of cord location and

keep it well away from the rotating wheel.

 INSPECT EXTENSION CORDS PERIODICALLY and

replace if damaged.

 GROUND ALL TOOLS. If tool is equipped with three-

prong plug, it should be plugged into a three-hole electri-

cal receptacle.

 CHECK WITH A QUALIFIED ELECTRICIAN or service

personnel if the grounding instructions are not completely

understood or if in doubt as to whether the tool is properly

grounded.

 USE ONLY CORRECT ELECTRICAL DEVICES: 3-wire

extension cords that have 3-prong grounding plugs and

3-pole receptacles that accept the tool's plug.

 DO NOT MODIFY the plug provided. If it will not fit the

outlet, have the proper outlet installed by a qualified

electrician.

 KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND

GREASE. Always use a clean cloth when cleaning. Never

use brake fluids, gasoline, petroleum-based products, or

any solvents to clean tool.

 STAY ALERT AND EXERCISE CONTROL. Watch what

you are doing and use common sense. Do not operate

tool when you are tired. Do not rush.

 DO NOT USE TOOL IF SWITCH DOES NOT TURN IT

ON AND OFF. Have defective switches replaced by an

authorized service center.

 USE ONLY CORRECT WHEELS. Do not use wheels with

incorrect size holes. Never use washers or arbor nuts that

are defective or incorrect. The maximum wheel capacity

of your saw is 7 in. (178 mm).

 BEFORE MAKING A CUT, BE SURE ALL ADJUST-

MENTS ARE SECURE.

 NEVER TOUCH WHEEL or other moving parts during

use.

NEVER START A TOOL WHEN ANY ROTATING COM-

PONENT IS IN CONTACT WITH THE WORKPIECE.

 DO NOT OPERATE A TOOL WHILE UNDER THE

INFLUENCE OF DRUGS, ALCOHOL, OR ANY

MEDICATION.

 WHEN SERVICING use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

 USE ONLY RECOMMENDED ACCESSORIES listed in

this manual or addendums. Use of accessories that are

not listed may cause the risk of personal injury. Instruc-

tions for safe use of accessories are included with the

accessory.

 DOUBLE CHECK ALL SET-UPS. Make sure wheel is tight

and not making contact with saw or workpiece before

connecting to power supply.

 ALWAYS SECURE WORKPIECE firmly against the rip

guide, miter guide, or bevel table.

 NEVER stand or have any part of your body in line with

the path of the wheel.

 NEVER attempt to free a stalled wheel without first turning

the saw OFF and disconnecting the saw from the power

source.

 IF THE POWER SUPPLY CORD IS DAMAGED, it must

be replaced only by the manufacturer or by an authorized

service center to avoid risk.

 AVOID AWKWARD OPERATIONS AND HAND

POSITIONS where a sudden slip could cause your hand

to move into the cutting tool.

 MAKE SURE THE WORK AREA HAS AMPLE LIGHTING

to see the work and that no obstructions will interfere with

safe operation BEFORE performing any work using the

saw.

 ALWAYS TURN OFF SAW before disconnecting it, to

avoid accidental starting when reconnecting to power

supply.

 THIS TOOL should have the following markings:

a) Wear eye protection.

b) Use splash hood for every operation for which it can

be used.

c) Disconnect saw before servicing, when changing

cutting wheels, and cleaning.

d) Use tool only with smooth edge cutting wheels free

of openings, grooves, and teeth.

e) Replace damaged cutting wheel before operating.

f) Do not fill water bath above water fill line.

 SAVE THESE INSTRUCTIONS. Refer to them

frequently and use to instruct other users. If you loan

someone this tool, loan them these instructions too.

SPECIFIC SAFETY RULES

1 2 3 4 5 ... 40

Comments to this Manuals

No comments

Ryobi WS721 User Manual Page 4

Comments to this Manuals

Related products and manuals for Power saws Ryobi WS721