Ryobi RLM140SP User Manual Page 18

  • Download
  • Add to my manuals
  • Print
  • Page
    / 81
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 17
17
English
GB
F D E I P NL S DK N FIN GR HU CZ RU RO PL SLO HR TR EST LT LV SK BG
For rear discharge of grass clippings, do not install the
grass catcher. To improve discharging performance,
raise the blade height setting.
For best performance, always cut off one-third or less
of the total height of the grass.
When cutting long grass, reduce walking speed to allow
for more effective cutting and a proper discharge of the
clippings.
Do not cut wet grass. It will stick to the underside of the
deck and prevent proper bagging or discharge of the
grass clippings.
New or thick grass may require a narrower cut path.
Clean the underside of the mower deck after each use
to remove grass clippings, leaves, dirt, and any other
accumulated debris.
SLOPE OPERATION (Fig. 6)
Slopes are a major factor related to slip and fall accidents
that can result in severe injury. Operation on slopes
requires extra caution. If you feel uneasy on a slope,
do not mow it. For your safety, do not attempt to mow
slopes greater than 15 degrees.
Mow across the face of slopes, not up and down. Exercise
extreme caution when changing direction on slopes.
Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles. Remove all objects such as rocks, tree
limbs, etc., which could be tripped over or thrown by
the blade.
Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your bal-
ance, release operator presence control immediately.
Do not mow near drop-offs, ditches, or embankments;
you could lose your footing or balance.
EMPTYING THE GRASS CATCHER (Fig. 7)
Stop the mower and wait for the blade to come to a
complete stop.
Lift the rear discharge door.
Grasp grass catcher by its handle and lift to remove
from mower.
Empty grass clippings.
Lift the rear discharge door and reinstall the grass
catcher.
STARTING THE ENGINE
Firmly push the primer bulb 3 times.
NOTE: This step is not usually necessary when starting
an engine that has already run for a few minutes.
Hold the operator presence control bar down against
the handle.
Pull the starter cord until the engine runs. Release the
starter cord slowly so the rope does not snap back.
NOTE: It may be necessary to repeat priming steps in
cooler weather. In warmer weather, overpriming may cause
flooding and engine will not start. If you do flood the engine,
wait a few minutes before attempting to start and DO NOT
repeat priming steps.
STOPPING THE ENGINE
Release the operator presence control bar and allow
the engine comes to a complete stop.
SETTING BLADE HEIGHT (Fig. 4)
When shipped, the wheels on the mower are set to a
low-cutting position. Before using the mower for the
first time, adjust the cutting position to the height best
suited for your lawn. The average lawn should be between
1-1/2 in. to 2 in. during cool months and between 2 in. and
3 in. during hot months.
To set the blade height:
To raise the blade height, grasp the height adjustment
lever and move it toward the back of the mower.
To lower the blade height, grasp the height adjustment
lever and move it toward the front of the mower.
SETTING HANDLE HEIGHT (Fig. 5)
The height of the handle can be easily adjusted for opera-
tor preference.
To adjust the handle height:
Remove the handle knob.
Slide out the handle bolt and adjust the height to the
other opening.
Reinstall the handle bolt and knob. Tighten the knob
securely.
Repeat on the other side of the handle.
MOWING TIPS
Make sure the lawn is clear of stones, sticks, wires, and
other objects that could damage the lawn mower blades
or engine. Such objects could be accidentally thrown by
the mower in any direction and cause serious personal
injury to the operator and others.
OPERATION
RLM140HP-25lgs 09Jun11.indd Sec1:17RLM140HP-25lgs 09Jun11.indd Sec1:17 6/11/09 3:30:12 PM6/11/09 3:30:12 PM
Page view 17
1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 80 81

Comments to this Manuals

No comments