Ryobi R1801M1 User Manual download pdf (Page 4)

SPECIFIC SAFETY RULES

ADDITIONAL SAFETY RULES

■■

■ Know your power tool. Read operator’s manual

carefully. Learn its applications and limitations, as

well as the specific potential hazards related to this

tool. Following this rule will reduce the risk of electric

shock, fire, or serious injury.

■■

■ Always wear safety glasses. Everyday eyeglasses

have only impact-resistant lenses; they are NOT

safety glasses. Following this rule will reduce the risk

of serious personal injury.

■■

■ Protect your lungs. Wear a face or dust mask if the

operation is dusty. Following this rule will reduce the

risk of serious personal injury.

■■

■ Protect your hearing. Wear hearing protection

during extended periods of operation. Following this

rule will reduce the risk of serious personal injury.

■■

■ Inspect tool cords periodically and, if damaged,

have repaired at your nearest authorized service

center. Constantly stay aware of cord location.

Following this rule will reduce the risk of electric shock

or fire.

■■

■ Check damaged parts. Before further use of the

tool, a guard or other part that is damaged should

be carefully checked to determine that it will oper-

ate properly and perform its intended function.

Check for alignment of moving parts, binding of

moving parts, breakage of parts, mounting, and any

other conditions that may affect its operation. A

guard or other part that is damaged should be

properly repaired or replaced by an authorized

service center. Following this rule will reduce the risk

of shock, fire, or serious injury.

■■

■ Do not abuse cord. Never carry the tool by the cord

or yank it to disconnect it from the receptacle. Keep

cord away from heat, oil, and sharp edges. Follow-

ing this rule will reduce the risk of electric shock or fire.

■■

■ Make sure your extension cord is in good condi-

tion. When using an extension cord, be sure to use

one heavy enough to carry the current your prod-

uct will draw. A wire gage size (A.W.G.) of at least

14 is recommended for an extension cord 50 feet

or less in length. A cord exceeding 50 feet is not

recommended. If in doubt, use the next heavier

gage. The smaller the gage number, the heavier the

cord. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating.

■■

■ Inspect for and remove all nails from lumber before

routing. Following this rule will reduce the risk of

serious personal injury.

■■

■ Drugs, alcohol, medication. Do not operate tool

while under the influence of drugs, alcohol, or any

medication. Following this rule will reduce the risk of

electric shock, fire, or serious personal injury.

■■

■ Save these instructions. Refer to them frequently and

use them to instruct others who may use this tool. If

you loan someone this tool, loan them these instruc-

tions also.

WARNING:

Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains

chemicals known to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and

other masonry products, and

• arsenic and chromium from chemically-treated

lumber.

Your risk from these exposures varies, depending

on how often you do this type of work. To reduce

your exposure to these chemicals: work in a well ven-

tilated area, and work with approved safety equip-

ment, such as those dust masks that are specially

designed to filter out microscopic particles.

SERVICE

■■

■ Tool service must be performed only by qualified

repair personnel. Service or maintenance performed

by unqualified personnel could result in a risk of injury.

■ When servicing a tool, use only identical replace-

ment parts. Follow instructions in the Maintenance

section of this manual. Use of unauthorized parts or

failure to follow Maintenance Instructions may create a

risk of electric shock or injury.

GENERAL SAFETY RULES

■■

■ Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact

hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the cutting tool “live” and

shock the operator.

1 2 3 4 5 6 7 8 9 ... 19 20

Comments to this Manuals

No comments

Ryobi R1801M1 User Manual Page 4

Comments to this Manuals

Related products and manuals for Routers Ryobi R1801M1