SAVE THIS MANUAL FOR FUTURE REFERENCEYour miter saw has been engineered and manufactured to our high standard for dependability, ease of operation, an
10FEATURESFig. 1PRODUCT SPECIFICATIONSBlade Arbor ... 5/8 in.Blade Inner Washer ...
11FEATURESFig. 3KNOW YOUR COMPOUND MITER SAWSee Figure 1.Before attempting to use this product, familiarize yourself with all operating features and s
12FEATURESPOSITIVE STOPS ON MITER TABLEPositive stops have been provided at 0°, 15°, 22-1/2°, 30°, and 45°. The 22-1/2° and 45° positive stops have be
13LOOSE PARTS LISTFig. 6WARNING:The use of attachments or accessories not listed might be hazardous and could cause serious personal injury.The follow
14ASSEMBLYUNPACKINGThis product requires assembly.n Carefully lift saw from the carton by the carrying handle and the saw base, and place it on a lev
15ASSEMBLYMITER LOCK HANDLESee Figure 8.To install the miter lock handle, place the threaded stud on the end of the miter lock handle into the threade
16ASSEMBLYREAR BRACKETSee Figure 12.WARNING:A rear bracket is included with this miter saw to prevent tipping if the saw arm is released suddenly. Do
17ASSEMBLYFig. 15STOP BLOCKSMALLWING SCREWTABLEEXTENSIONFig. 16STOPBLOCKBASESTOP BLOCKSee Figures 15 -16.The stop block is included with the table ext
18ASSEMBLYTO INSTALL / REPLACE THE BLADESee Figures 17 - 18.WARNING:A 12 in. blade is the maximum blade capacity of the saw. Never use a blade that is
19ASSEMBLYWARNING:Make sure the spindle lock button is not engaged before reconnecting saw into power source. Never engage spindle lock
2n Introduction ...
20ASSEMBLYFig. 21VIEW OF MITER TABLE SQUARE WITH FENCE MITERLOCK PLATEMITERLOCK HANDLESLIDING MITER FENCEMITER TABLETHROAT PLATEFRAMING SQUARENOTE: Ma
21ASSEMBLYSQUARING THE BLADE TO THE FENCESee Figures 25 - 27.n Unplug the saw.n Pull the saw arm all the way down and engage the lock pin to hold th
22ASSEMBLYSCALEINDICATORFig. 28MITERSCALEINDICATORSCREWBEVEL SCALESQUARING THE BLADE TO THE MITER TABLESee Figures 29 - 31.n Unplug the saw.n Pull t
23OPERATIONWARNING:Do not allow familiarity with tools to make you care-less. Remember that a careless fraction of a second issufficient to i
24OPERATIONn Release the miter lock plate. NOTE: You can quickly locate 0°, 22-1/2° left or right, and 45° left or right by releasing the lock plate
25OPERATIONn The 45° triangle on the miter fence provides for the maximum clearance required for adjusting the miter saw’s angle when making
26OPERATIONn Place the workpiece flat on the miter table with one edge securely against the fence. If the board is warped, place the convex side agai
27OPERATION4 PITCH OF SIDENUMBER OF SIDES0°6M- 45.00°B- 0.00°5°10°15°20°25°30°35°40°45°50°55°60°65°70°75°80°85°90°578 910M- 36.00°B- 0.00°M- 3
28OPERATIONWhen setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes the
29OPERATIONWRONGWARNING: To avoid a kickback and to avoid serious personal injury, never position the concave edge of bowed or warped material against
3GENERAL SAFETY RULESWARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fir
30ADJUSTMENTSWARNING:Before performing any adjustment, make sure the tool is unplugged from the power supply. Failure to heed this warning could resul
31MAINTENANCEWARNING:When servicing, use only identical replacement parts. Use of any other parts may create a hazard or cause product
32Fig. 47ALKALINECELLALKALINECELLALKALINECELLNEGATIVE (–)LASER GUIDESUPPORTBATTERIESCHANGING THE BATTERIESSee Figures 46 - 47.n Unplug the saw.n Remo
33NOTES
RYOBI TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Post Office Box 1207, Anderson, SC 29622-1207Phone 1-800-525-2579www.ryobitools.com
4GENERAL SAFETY RULESn NEVER USE IN AN EXPLOSIVE ATMOSPHERE.Normal sparking of the motor could ignite fumes.n INSPECT TOOL CORDS PERIODICALL
5n NEVER hand hold a workpiece that is too small to be clamped. Keep hands clear of the cutting area.n NEVER reach behind, under, or within three in
6SYMBOLSSome of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpreta-tion of these symbols wil
7SYMBOLSSERVICEServicing requires extreme care and knowledge and should be performed only by a qualified service technician. For service we su
8EXTENSION CORDSWhen using a power tool at a considerable distance from a power source, be sure to use an extension cord that has the capacity to h
9GLOSSARY OF TERMSNon-Through CutsAny cutting operation where the blade does not extend completely through the thickness of the workpiece.Push
Comments to this Manuals