Ryobi A99DLK1 User Manual

Browse online or download User Manual for Accessories for video Ryobi A99DLK1. Ryobi A99DLK1 User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 2
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Fig. 1
A - Bracket (support, soporte)
B - Auto-strike locator (localisateur à martelage automatique, indicador de
posición con golpe automático)
C - Hole centering marks (point central, marca de centro)
D - Mortise (mortaise, mortaja)
B
A
D
Fig. 3
Fig. 4
C
A - Bracket (support, soporte)
B - 1 in. spade bit [foret à trois, pointes de 25,4 mm (1 po), broca de pala
de 25,4 mm (1 pulg.)]
C - 1-1/2 in. hole saw [scie cloche au carbone de 38,1 mm (1-1/2 po) sierra
de perforación de carbono de 38,1 mm (1-1/2 pulg.)]
D - 2-1/8 in. hole saw [scie cloche au carbone de 53, 98 mm (2-1/8 po),
sierra de perforación de carbono de 53,98 mm (2-1/8 pulg.)]
E - Arbor with pilot bit and arbor nut (arbre avec mèche pilote et écrou
d’arbre, mandril con broca piloto y tuerca del árbol)
F - 1/8 in. brad point drill bit [foret de 3,18 mm (1/8 po), punta de
destornillador de 3,18 mm (1/8 pulg.)]
G - 3/32 in. drill bit [foret de 2,4 mm (3/32 po), punta de destornillador de
2,4 mm (3/32 pulg.)]
H - PH2/8-10SL double ended bit (embout double 8-10SL 2, broca de
doble extremo 8-10SL N.º 2)
Fig. 2 Fig. 5
Fig. 6
A - Arbor with pilot bit and arbor nut (arbre avec mèche pilote et écrou
d’arbre, mandril con broca piloto y tuerca del árbol)
B - Carbon hole saw (scie cloche au carbone, sierra de perforación de
carbono )
C - Arbor with pilot bit (arbre avec mèche pilote, mandril con broca piloto)
D - Arbor nut (écrou d’arbre, tuerca del árbol)
E - Hole saw assembly (sssemblage de la scie-cloche, conjunto de la sierra
de perforación)
A - Tap with hammer (taper à l’aide d’un marteau, golpear con un martillo)
A - To drill cross bore (pour percer le trou transversal, para perforar orificio
transversal)
B - To drill latch bore (pour percer le trou du loquet, para perforar orificio de
pestillo)
WOOD DOOR LOCK
INSTALLATION KIT
A99DLK1
WARNING:
To reduce the risk of injury, do not attempt to use this
product until you have read thoroughly and understand
completely this operator's manual and the operator’s
manual for any power tools used.
PACKING LIST
See Figure 1.
Bracket
1 in. Spade Bit
1-1/2 in. Carbon Hole Saw
2-1/8 in. Carbon Hole Saw
Arbor with Pilot Bit and Arbor Nut
1/8 in. Brad Point Drill Bit
3/32 in. Drill Bit
PH2/8-10SL Double Ended Bit
TOOLS NEEDED
Hammer
AC Power Drill or DC Drill 18 Volts or more
APPLICATIONS
You may use this tool for the following purpose:
Installing lock sets and dead bolts easily and accurately
without measuring.
INSTRUCTIONS
See Figures 2 - 6.
Position the bracket on the door using auto-strike locator.
Line up auto-strike locator with center of the mortise in the
door jamb and slide into mortise.
Using a hammer, firmly tap the desired backset location
(shown on instructions included with door hardware) and
latch bore location using bracket centering points.
NOTE: Both hole center points can be marked if unsure
at this point which backset length to use.
Carefully remove bracket from door. Pulling auto-strike
locators away from surface of door to avoid scratching
wood surface.
Using hole saw (included) drill cross bore hole first (see
hardware instructions for hole size).
Assemble hole saw. Remove arbor nut from arbor with
pilot bit. Insert arbor with pilot bit through hole saw lining
up flats. Securely tighten arbor nut onto arbor with pilot
bit, see figure 5.
Follow drill manual instructions to install hole saw into
chuck.
For a straight hole, be sure drill is at a right angle to the
door so hole saw enters the wood evenly.
Drill from one side until pilot bit shows on opposite side
of door. Drill on opposite side, lining up pilot bit hole with
pilot bit. Meet the two holes in the center of door.
Using the 1 in. spade bit, drill latch bore. Keep drill at a
right angle to door flat to ensure straight hole.
NOTE: For 1-3/4 in. door, the latch bore is automatically
centered. For 1-3/8 in. door, center the door within the
window, firmly tap the latch bore location while holding
the bracket in place.
Follow instructions included with door hardware for
installation. Use included drill bits and double ended bit
to install hardware.
NOTE: General household cleaner may be used to remove
any scuff marks left behind from the bracket.
If installing a lock set with a rectangular, flush mounted
strike plate, use the RYOBI Door Latch Installation Kit
(Model# A99LM1)
A
A - Cross bore (trou transversal, orificio transversal)
B - Backset (appui, distancia al centro del picaporte)
C - Latch bore (trou du loquet, orificio del pestillo)
D - Center mark (point central, marca de centro)
B
C
D
D
A
B
C
D
D
C
F
G
H
E
B
A
E
A
A
B
Page view 0
1 2

Summary of Contents

Page 1 - INSTALLATION KIT

Fig. 1A - Bracket (support, soporte)B - Auto-strike locator (localisateur à martelage automatique, indicador de posición con golpe automático)C - Hole

Page 2 - ONE WORLD TECHNOLOGIES, INC

ONE WORLD TECHNOLOGIES, INC.1428 Pearman Dairy Road, Anderson, SC 29625Phone 1-800-525-2579www.ryobitools.comFRANÇAISESPAÑOLTROUSSE D’INSTALLATION POU

Comments to this Manuals

No comments